제조사 | EKSPLA UAB |
---|---|
가격 | TBD |
문의 | 02-3461-1103 |
PL2210 series diode-pumped, air-cooled, mode-locked Nd:YAG lasers provide picosecond pulses at a kilohertz pulse repetition rate. Short pulse duration, excellent pulse-to-pulse stability, superior beam quality makes PL2210 series diode pumped picosecond lasers well suited for many applications, including material processing, time-resolved spectroscopy, optical parametric generator pumping, and other tasks.
PL2210 series lasers offer a number of optional items that extend the capabilities of the laser. A pulse picker option allows control of
the pulse repetition rate of the laser and operation in single-shot mode. The repetition rate and timing of pulses can be locked to an external RF source (with –PLL option) or other ultrafast laser system (with –FS option). The laser provides a triggering pulse for synchronization of the customer‘s equipment. A low jitter SYNC OUT pulse has a lead up to 500 ns that can be adjusted in ~0.25 ns steps from a PC.
Up to 400 μs lead of triggering pulse is available as a PRETRIG standard feature that is designed to provide precise, very low jitter trigger pulses for a streak camera.
Automated angle-tuned non-linear crystals mounted in temperature stabilized heaters are used for second, third and fourth high spectral purity harmonic generation.
The laser can be operated from personal computer through USB (RS-232 is optional) interface using supplied LabVIEW™ drivers or from remote control pad with backlit display that is easy to read even while wearing laser safety glasses.
Model | Features |
---|---|
PL2210A-1k | Up to 900 μJ, 28 ps pulses at an up to 1 kHz repetition rate |
PL2211 | Up to 2.5 mJ energy at a 1 kHz repetition rate at 28 ps pulses |
PL2211A | Up to 5 mJ energy at a 1 kHz repetition rate at 28 ps pulses |
Model | Features |
---|---|
PL2210A-2k | Up to 400 μJ, 28 ps pulses at an up to 2 kHz repetition rate |
PL2210B | Up to 2.5 mJ energy at a 1 kHz repetition rate at 80 ps pulses |
PL2210B-TR | Model, in addition to a 1 kHz pulse train, has an output of 88 MHz pulse train with 5 W average power that can be used for pumping synchronously pumped OPOs |
Model | PL2210A-1k | PL2211 | PL2211A |
---|---|---|---|
MAIN SPECIFICATIONS 1) | |||
Output energy | |||
at 1064 nm | 0.9 mJ | 2.5 mJ | 5 mJ |
at 532 nm 2) | 0.45 mJ | 1.3 mJ | 2.5 mJ |
at 355 nm 3) | 0.35 mJ | 0.8 mJ | 1.6 mJ |
at 266 nm 4) | 0.16 mJ | 0.5 mJ | 1 mJ |
Pulse energy stability (Std. Dev) 5) | |||
at 1064 nm | 0.5 % | ||
at 532 nm | 0.8 % | ||
at 355 nm | 1 % | ||
at 266 nm | 2 % | ||
Pulse duration (FWHM) 6) | 28 ps ± 10 % | ||
Pulse repetition rate | 1 kHz | ||
Triggering mode | internal/external | ||
Typical TRIG1 OUT pulse delay 8) | -500...50 ns | ||
TRIG1 OUT pulse jitter | <0.1 ns rms | ||
Spatial mode 9) | Close to Gaussian | ||
Beam divergence 10) | <1 mrad | ||
Beam diameter 11) | ~3 mm | ||
Beam pointing stability 12) | <30 μrad | ||
Pre-pulse contrast | >200:1 | ||
Polarization | linear, >100:1 | ||
PHYSICAL CHARACTERISTICS | |||
Laser head size (W × L × H) 13) | 456 × 1031 × 249 mm | ||
Power supply size (W × L × H) | 365 × 392 × 290 mm | 550 × 600 × 550 ±3 mm (19″ standard, MR-9) | |
OPERATING REQUIREMENTS | |||
Water service | not required, air cooled | ||
Relative humidity | 20 – 80 % (non condensing) | ||
Ambient temperature | 22 ± 2 °C | ||
Power requirements | 100 – 240 V AC, single phase 50/60 Hz | ||
Power consumption 14) | <1 kW | <1.5 kW |
Note: Laser must be connected to the mains electricity all the time. If there will be no mains electricity for longer that 1 hour then laser (system) needs warm up for a few hours before switching on.
Provides low jitter pulse for streak camera triggering with lead/delay in -400…600 μs range and <10 ps rms jitter.
Provides 80 ps ± 10 % output pulse duration. Inquire for pulse energy specifications.
Provides 22 ps ± 10 % output pulse duration. Inquire for pulse energy specifications.
Allows reduction of the pulse repetition rate of the PL2210 series laser by integer numbers. Single shot mode is also possible. In addition, the –PC option reduces the low-intensity quasi-CW background that is present at laser output at 1064 nm wavelength. Please note that the output of fundamental wavelength and harmonics will be reduced by approx. 20% with installation of the –PC option.