1400 – 4450 nm tuning range
Up to 300 mW output
Up to 87 MHz repetition rate
Nearly Fourier transform-limited linewidth
| 제조사 | 레이비스 |
|---|---|
| 가격 | TBD |
| 문의 | 02-3461-1103 |
PT277 series
- Picosecond MHz rate NIR-IR range laser system
- 1400 – 4450 nm tuning range
- Up to 300 mW output
- Up to 87 MHz repetition rate
- Nearly Fourier transform-limited linewidth
Features & Applications
FEATURES
- 1400 – 4450 nm tuning range
- Nearly Fourier transform-limited linewidth
- Nearly diffraction limited divergence
- Output wavelength monitoring (optional)
- PC control via USB (RS232 is optional) and LabView™ drivers
APPLICATIONS
- Infrared microscopy
- Infrared spectroscopy
Description
PT277 series laser systems integrate a picosecond optical parametric oscillator and DPSS pump laser into a single compact housing. Mounting the components into one frame provides a cost-effective and robust solution with improved long-term stability and reduced maintenance costs.
The tuning range is for the model PT277 1400 – 2050 and 2200 to 4450 nm with nearly Fourier transform limited linewidth.
The microprocessor-controlled wavelength tuning is fully automatic. The wavelength controlling elements are mounted on precise micro‑stepping motors. The temperature of the non‑linear crystal is controlled by a precise thermocontroller with a bidirectional Peltier element, resulting in the fast tuning of crystal temperature. For customer convenience the system can be controlled through its USB type PC interface (RS232 is optional) with LabView™ drivers or a user-friendly remote control pad. Both options allow easy control of system settings.
Specifications
| Model | PT277 |
|---|---|
| OPO/OPG SPECIFICATIONS 1) | |
| Pulse repetition rate 2) | 87 MHz |
| Tuning range | |
| Signal | 1400 – 2050 nm |
| Idler | 2200 – 4450 nm |
| Output power 3) | |
| OPO/OPG 4) | 300 mW |
| Linewidth 4) | < 0.3 cm-1 |
| Typical pulse duration 4) 5) | 70 ps |
| Scanning step | |
| Signal | 0.1 nm |
| Idler | 0.1 nm |
| Polarization | |
| Signal beam | horizontal |
| Idler beam | horizontal |
| Typical beam diameter 4) 6) | ~2 mm |
| Typical beam diameter, Idler 4) 6) | ~5 mm |
| Typical beam divergence 4) 7) | < 2 mrad |
| PHYSICAL CHARACTERISTICS | |
| Unit size (W×L×H) | 370 × 800 × 260 mm |
| Power supply size (W×L×H) | 520 × 500 × 290 mm |
| Umbilical length | 2 m |
| OPERATING REQUIREMENTS | |
| Cooling | air |
| Room temperature | 22 ± 2 °C |
| Relative humidity | 20 – 80 % (noncondensing) |
| Power requirements | 100 – 240 V AC, single phase 50/60 Hz |
| Power consumption | < 1 kVA |
- Due to continuous improvement, all specifications are subject to change without notice. Parameters marked ‘typical’ are indications of typical performance (not specifications) and will vary with each unit we manufacture. Unless stated otherwise, all specifications are measured at 1064 nm and for basic system without options.
- Inquire for custom pulse repetition rates.
- Output powers are specified at selected wavelengths. See typical tuning curves for power at other wavelengths.
- Measured at 1620 nm for PT277 model at signal range.
- Pulse duration can vary depending on wavelength and pump energy.
- Beam diameter at the 1/e2 level and can vary depending on the pump pulse energy.
- Full angle measured at the FWHM level.
Note: Laser must be connected to the mains electricity all the time. If there will be no mains electricity for longer that 1 hour then laser (system) needs warm up for a few hours before switching on.
